XE2AD-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object XE2AD-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1781683335	29.5 C	38.98 %	1024.63 hPa
1781678266	26.9 C	47.47 %	1024.38 hPa
1781678147	26.8 C	47.81 %	1025.13 hPa
1781678114	26.8 C	47.81 %	1026.5 hPa
1781678066	26.7 C	48.27 %	1025.38 hPa
1781677966	26.5 C	49.19 %	1025.88 hPa
1781677881	26.4 C	49.65 %	1030 hPa
1781677853	26.4 C	49.9 %	1029.88 hPa
1781677826	26.4 C	49.9 %	1028.5 hPa
1781677802	26.3 C	50.37 %	1028.75 hPa
1781677739	26.2 C	50.77 %	1025.63 hPa
1781677573	26.1 C	51.34 %	1028.5 hPa
1781677334	25.9 C	54.81 %	0 hPa
1781677298	25.7 C	56.08 %	1027.5 hPa
1781676957	25 C	57.84 %	1021.5 hPa
1781639565	34.2 C	28.59 %	1018 hPa
1781639253	34.4 C	28.17 %	974.75 hPa
1781638883	34.6 C	28.12 %	970.63 hPa
1781637979	34.9 C	27.71 %	1001.5 hPa
1781637075	34.5 C	28.48 %	1001.38 hPa
1781637051	34.5 C	28.48 %	975.88 hPa
1781637022	34.4 C	28.37 %	972.5 hPa
1781636921	34.4 C	28.63 %	976.38 hPa
1781635992	33.5 C	29.02 %	1014.75 hPa
1781634811	34.8 C	27.27 %	1020.75 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)