This is the latest recevied telemetry packets stored in our database for station/object DB0TAN. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Vin*
Temp*
0*
0*
0*
1773218125
14.33 Volt
5 C
0 0
0 0
0 0
1773217225
14.25 Volt
5 C
0 0
0 0
0 0
1773216326
14.25 Volt
5 C
0 0
0 0
0 0
1773215425
14.25 Volt
5 C
0 0
0 0
0 0
1773214526
14.25 Volt
5 C
0 0
0 0
0 0
1773213625
14.25 Volt
5 C
0 0
0 0
0 0
1773212726
14.25 Volt
4.5 C
0 0
0 0
0 0
1773211826
14.25 Volt
4.5 C
0 0
0 0
0 0
1773210926
14.25 Volt
4.5 C
0 0
0 0
0 0
1773210026
14.25 Volt
4.5 C
0 0
0 0
0 0
1773209126
14.33 Volt
4.5 C
0 0
0 0
0 0
1773208226
14.25 Volt
4.5 C
0 0
0 0
0 0
1773207326
14.25 Volt
4.5 C
0 0
0 0
0 0
1773206426
14.25 Volt
4.5 C
0 0
0 0
0 0
1773205526
14.25 Volt
4.5 C
0 0
0 0
0 0
1773204626
14.25 Volt
4.5 C
0 0
0 0
0 0
1773203726
14.25 Volt
4.5 C
0 0
0 0
0 0
1773202826
14.25 Volt
4.5 C
0 0
0 0
0 0
1773201926
14.25 Volt
4.5 C
0 0
0 0
0 0
1773201026
14.25 Volt
5 C
0 0
0 0
0 0
1773200126
14.25 Volt
5 C
0 0
0 0
0 0
1773199226
14.25 Volt
5 C
0 0
0 0
0 0
1773198326
14.25 Volt
5 C
0 0
0 0
0 0
*Used Equation Coefficients:
Vin: 0, 0.075, 0
Temp: 0, 0.5, -64
0: 0, 0, 0
0: 0, 0, 0
0: 0, 0, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)