YO3FBD-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3FBD-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp_interioara*	Temp_exterioara*	Temp_TX_RoLink*
1758015371	35.6 C	28.1 C	38.3 C
1758014770	35.4 C	27.4 C	39.1 C
1758014170	35.4 C	27.1 C	41.9 C
1758013565	35.3 C	26.8 C	48.6 C
1758012965	34.6 C	26.3 C	39.3 C
1758012370	34.6 C	26.3 C	38.8 C
1758011770	34.3 C	26.1 C	35.6 C
1758011170	34.1 C	25.2 C	35.6 C
1758010570	33.8 C	24.9 C	34.6 C
1758009965	33.4 C	24.9 C	34 C
1758009366	33.3 C	23.9 C	33.8 C
1758008771	33.4 C	23.9 C	33.6 C
1758008171	33.4 C	23.9 C	33.1 C
1758007571	32.9 C	23.3 C	32.7 C
1758006971	32.6 C	22.4 C	32.3 C
1758006365	32.2 C	22.6 C	31.8 C
1758005765	31.8 C	21.8 C	31.3 C
1758005172	31.2 C	21.6 C	30.8 C
1758004570	31.2 C	21.4 C	30.2 C
1758003970	30.8 C	20.5 C	29.4 C
1758003370	30.1 C	20.4 C	28.6 C
1758002765	29.2 C	19.7 C	27.9 C
1758002165	28.1 C	18.8 C	27.7 C
1758001570	27 C	18 C	24.8 C
1758000970	25.9 C	17 C	23.6 C

*Used Equation Coefficients:

Temp_interioara: 0, 1, -100

Temp_exterioara: 0, 1, -100

Temp_TX_RoLink: 0, 1, -100

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)