HS6NDK-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS6NDK-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Dg1h*	Eff1h*
1780552385	14.22 Volt	280 Pkt	40 Pcnt
1780548785	14.22 Volt	370 Pkt	40 Pcnt
1780545185	14.14 Volt	280 Pkt	40 Pcnt
1780541586	14.22 Volt	270 Pkt	40 Pcnt
1780537986	14.22 Volt	270 Pkt	40 Pcnt
1780534386	14.22 Volt	600 Pkt	40 Pcnt
1780530786	14.22 Volt	280 Pkt	40 Pcnt
1780527186	14.22 Volt	440 Pkt	40 Pcnt
1780523586	14.22 Volt	530 Pkt	40 Pcnt
1780519986	14.14 Volt	400 Pkt	40 Pcnt
1780516386	14.22 Volt	400 Pkt	40 Pcnt
1780512786	14.22 Volt	540 Pkt	40 Pcnt
1780509186	14.22 Volt	370 Pkt	40 Pcnt
1780505586	14.22 Volt	250 Pkt	40 Pcnt
1780502129	14.22 Volt	440 Pkt	40 Pcnt
1780498387	14.22 Volt	360 Pkt	40 Pcnt
1780494787	14.22 Volt	570 Pkt	40 Pcnt
1780491187	14.22 Volt	370 Pkt	40 Pcnt
1780487587	14.22 Volt	250 Pkt	40 Pcnt
1780483987	14.22 Volt	500 Pkt	40 Pcnt
1780480387	14.22 Volt	180 Pkt	40 Pcnt
1780476787	14.22 Volt	100 Pkt	40 Pcnt
1780473187	14.22 Volt	330 Pkt	40 Pcnt
1780469587	14.22 Volt	450 Pkt	40 Pcnt
1780465987	14.22 Volt	280 Pkt	40 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)