OE3BCB-22 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3BCB-22. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	press*	temp.in*	temp.out*
1788706804	444 hPa	0 C deg	0 C deg
1788706203	444 hPa	0 C deg	0 C deg
1788705604	439 hPa	0 C deg	0 C deg
1788705004	433 hPa	0 C deg	0 C deg
1788704404	433 hPa	0 C deg	0 C deg
1788703804	433 hPa	0 C deg	0 C deg
1788703203	428 hPa	0 C deg	0 C deg
1788702604	422 hPa	0 C deg	0 C deg
1788701403	422 hPa	0 C deg	0 C deg
1788700803	417 hPa	0 C deg	0 C deg
1788700203	417 hPa	0 C deg	0 C deg
1788699604	422 hPa	0 C deg	0 C deg
1788699004	428 hPa	0 C deg	0 C deg
1788698404	422 hPa	0 C deg	0 C deg
1788697804	417 hPa	0 C deg	0 C deg
1788697205	412 hPa	0 C deg	0 C deg
1788696603	412 hPa	0 C deg	0 C deg
1788696004	412 hPa	0 C deg	0 C deg
1788695403	412 hPa	0 C deg	0 C deg
1788694804	406 hPa	0 C deg	0 C deg
1788694229	406 hPa	0 C deg	0 C deg
1788693003	401 hPa	0 C deg	0 C deg
1788692404	401 hPa	0 C deg	0 C deg
1788691804	401 hPa	0 C deg	0 C deg
1788691204	401 hPa	0 C deg	0 C deg

*Used Equation Coefficients:

press: 0, 1, 0

temp.in: 0, 1, 0

hum: 0, 1, 0

QNH: 0, 1, 0

temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)