KL7AIR-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KL7AIR-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1781601119	14.03 Volt	100 Pkt	40 Pkt	64 Pcnt
1781600819	14.03 Volt	100 Pkt	40 Pkt	63 Pcnt
1781600819	14.03 Volt	100 Pkt	40 Pkt	63 Pcnt
1781600519	14.03 Volt	110 Pkt	40 Pkt	63 Pcnt
1781600219	14.03 Volt	100 Pkt	40 Pkt	61 Pcnt
1781600219	14.03 Volt	100 Pkt	40 Pkt	61 Pcnt
1781599919	14.03 Volt	110 Pkt	40 Pkt	61 Pcnt
1781599619	14.03 Volt	100 Pkt	40 Pkt	62 Pcnt
1781599619	14.03 Volt	100 Pkt	40 Pkt	62 Pcnt
1781599319	14.03 Volt	100 Pkt	40 Pkt	60 Pcnt
1781599019	14.03 Volt	100 Pkt	40 Pkt	61 Pcnt
1781599019	14.03 Volt	100 Pkt	40 Pkt	61 Pcnt
1781598719	14.03 Volt	100 Pkt	40 Pkt	62 Pcnt
1781598420	14.03 Volt	100 Pkt	50 Pkt	61 Pcnt
1781598419	14.03 Volt	100 Pkt	50 Pkt	61 Pcnt
1781598141	14.03 Volt	110 Pkt	50 Pkt	63 Pcnt
1781597820	14.03 Volt	100 Pkt	50 Pkt	63 Pcnt
1781597819	14.03 Volt	100 Pkt	50 Pkt	63 Pcnt
1781597519	14.03 Volt	100 Pkt	40 Pkt	62 Pcnt
1781597220	14.03 Volt	90 Pkt	40 Pkt	64 Pcnt
1781597219	14.03 Volt	90 Pkt	40 Pkt	64 Pcnt
1781596919	14.03 Volt	90 Pkt	30 Pkt	63 Pcnt
1781596620	14.03 Volt	90 Pkt	40 Pkt	63 Pcnt
1781596619	14.03 Volt	90 Pkt	40 Pkt	63 Pcnt
1781596319	14.03 Volt	80 Pkt	30 Pkt	58 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)