DL7AD-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL7AD-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vbat*	Vsol*	Psys*	AirP*
1788262012	4.03 V	0 V	254 mW	500 Pa
1788261993	4.04 V	0 V	352 mW	500 Pa
1788261949	4.06 V	0 V	252 mW	500 Pa
1788261765	4.06 V	0 V	252 mW	500 Pa
1788261754	4.02 V	0 V	338 mW	500 Pa
1788261702	4.03 V	0 V	246 mW	500 Pa
1788261468	3.94 V	0 V	252 mW	500 Pa
1788261399	4.03 V	0 V	246 mW	500 Pa
1788261381	4.06 V	0.01 V	324 mW	500 Pa
1788261319	4.04 V	0 V	264 mW	500 Pa
1788261080	4.04 V	0 V	264 mW	500 Pa
1788260819	4.04 V	0 V	264 mW	500 Pa
1788260578	4.04 V	0 V	264 mW	500 Pa
1788260308	4.04 V	0 V	482 mW	500 Pa
1788260181	3.94 V	0 V	246 mW	500 Pa
1788260081	4.04 V	0 V	364 mW	500 Pa
1788260079	4.06 V	0 V	348 mW	500 Pa
1788260031	3.95 V	0 V	262 mW	500 Pa
1788259276	3.95 V	0 V	264 mW	500 Pa
1788259120	3.95 V	0 V	252 mW	500 Pa
1788259031	3.95 V	0 V	252 mW	500 Pa
1788259027	3.96 V	0 V	300 mW	500 Pa
1788258981	3.94 V	0 V	264 mW	500 Pa
1788258823	3.94 V	0 V	264 mW	500 Pa
1788258651	3.94 V	0 V	264 mW	500 Pa

*Used Equation Coefficients:

Vbat: 0, 0.001, 0

Vsol: 0, 0.001, 0

Psys: 0, 2, 0

Temp: 0, 0.1, -100

AirP: 0, 12.5, 500

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)