OE3VPA-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3VPA-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1788632579	13.75 Volt	770 pkt	76 Pcnt
1788632279	13.75 Volt	760 pkt	76 Pcnt
1788631979	13.75 Volt	760 pkt	76 Pcnt
1788631679	13.75 Volt	740 pkt	75 Pcnt
1788631378	13.75 Volt	750 pkt	75 Pcnt
1788631078	13.75 Volt	750 pkt	76 Pcnt
1788630778	13.75 Volt	740 pkt	75 Pcnt
1788630477	13.75 Volt	750 pkt	76 Pcnt
1788630177	13.67 Volt	750 pkt	76 Pcnt
1788629877	13.67 Volt	750 pkt	76 Pcnt
1788629577	13.67 Volt	740 pkt	75 Pcnt
1788629276	13.67 Volt	740 pkt	75 Pcnt
1788628976	13.59 Volt	730 pkt	76 Pcnt
1788628676	13.59 Volt	720 pkt	76 Pcnt
1788628375	13.51 Volt	740 pkt	77 Pcnt
1788628075	13.35 Volt	750 pkt	77 Pcnt
1788627802	12.96 Volt	740 pkt	77 Pcnt
1788627475	12.96 Volt	740 pkt	78 Pcnt
1788627174	12.96 Volt	760 pkt	78 Pcnt
1788626874	12.96 Volt	750 pkt	78 Pcnt
1788626574	13.04 Volt	760 pkt	79 Pcnt
1788626273	13.04 Volt	770 pkt	80 Pcnt
1788625974	13.04 Volt	780 pkt	81 Pcnt
1788625673	13.04 Volt	790 pkt	81 Pcnt
1788625372	13.04 Volt	790 pkt	81 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)