UR4UWA-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UR4UWA-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Eff1h*	Eff*
1776611079	12.3 Volt	40 Pcnt	61 Pcnt
1776602671	12.3 Volt	36 Pcnt	61 Pcnt
1776530602	12.3 Volt	81 Pcnt	61 Pcnt
1776526999	12.38 Volt	85 Pcnt	61 Pcnt
1776510182	12.38 Volt	20 Pcnt	61 Pcnt
1776506579	12.38 Volt	100 Pcnt	62 Pcnt
1776095785	12.3 Volt	50 Pcnt	75 Pcnt
1776094583	12.3 Volt	0 Pcnt	75 Pcnt
1776059750	12.3 Volt	83 Pcnt	77 Pcnt
1776058549	12.3 Volt	88 Pcnt	77 Pcnt
1776054945	12.38 Volt	87 Pcnt	76 Pcnt
1776051342	12.38 Volt	83 Pcnt	76 Pcnt
1776046537	12.3 Volt	75 Pcnt	76 Pcnt
1776033325	12.3 Volt	25 Pcnt	77 Pcnt
1776032123	12.3 Volt	14 Pcnt	77 Pcnt
1776030922	12.3 Volt	16 Pcnt	77 Pcnt
1776029721	12.3 Volt	20 Pcnt	78 Pcnt
1776026118	12.38 Volt	0 Pcnt	79 Pcnt
1776022514	12.3 Volt	66 Pcnt	80 Pcnt
1776021313	12.3 Volt	57 Pcnt	80 Pcnt
1776020112	12.38 Volt	50 Pcnt	80 Pcnt
1775999692	12.3 Volt	88 Pcnt	84 Pcnt
1775996089	12.3 Volt	83 Pcnt	84 Pcnt
1775912008	12.3 Volt	0 Pcnt	83 Pcnt
1775880778	12.38 Volt	100 Pcnt	87 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 1, 0

Dg1h: 0, 1, 0

Eff1h: 0, 1, 0

Eff: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)