LZ1RZZ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ1RZZ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Outside Temperature*	Air Humidity*	Atmospheric pressure*
1780610701	18.6 Deg.C	100 Percent	989 hPa
1780610402	19.7 Deg.C	100 Percent	991 hPa
1780610102	20.5 Deg.C	100 Percent	992 hPa
1780609802	18.5 Deg.C	100 Percent	989 hPa
1780609502	17.6 Deg.C	100 Percent	987 hPa
1780609202	19.3 Deg.C	100 Percent	990 hPa
1780608902	18.8 Deg.C	100 Percent	989 hPa
1780608602	18.7 Deg.C	100 Percent	989 hPa
1780608302	18.3 Deg.C	100 Percent	987 hPa
1780608002	20.6 Deg.C	100 Percent	992 hPa
1780607701	20.7 Deg.C	100 Percent	992 hPa
1780607403	20.3 Deg.C	100 Percent	991 hPa
1780607102	21 Deg.C	100 Percent	992 hPa
1780606802	19.3 Deg.C	100 Percent	990 hPa
1780606502	20.1 Deg.C	100 Percent	990 hPa
1780606201	21 Deg.C	100 Percent	992 hPa
1780605902	20.9 Deg.C	100 Percent	992 hPa
1780605603	21.2 Deg.C	100 Percent	992 hPa
1780605302	21.1 Deg.C	100 Percent	992 hPa
1780605002	20.7 Deg.C	100 Percent	991 hPa
1780604702	21.5 Deg.C	100 Percent	992 hPa
1780604402	21.2 Deg.C	100 Percent	992 hPa
1780604102	21.2 Deg.C	100 Percent	992 hPa
1780603801	21.5 Deg.C	100 Percent	992 hPa
1780603502	21 Deg.C	100 Percent	991 hPa

*Used Equation Coefficients:

Outside Temperature: 0, 0.1, 0

Air Humidity: 0, 1, 0

Atmospheric pressure: 0, 1, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)