KF5SMH-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KF5SMH-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1781700823	13.88 Volt	190 Pkt	72 Pcnt
1781700523	13.88 Volt	190 Pkt	72 Pcnt
1781700223	13.88 Volt	190 Pkt	73 Pcnt
1781699923	13.88 Volt	180 Pkt	74 Pcnt
1781699623	13.88 Volt	180 Pkt	73 Pcnt
1781699323	13.88 Volt	190 Pkt	73 Pcnt
1781699023	13.88 Volt	190 Pkt	73 Pcnt
1781698723	13.88 Volt	190 Pkt	73 Pcnt
1781698423	13.88 Volt	200 Pkt	73 Pcnt
1781698123	13.88 Volt	200 Pkt	73 Pcnt
1781697823	13.88 Volt	200 Pkt	74 Pcnt
1781697523	13.88 Volt	200 Pkt	72 Pcnt
1781697223	13.88 Volt	210 Pkt	72 Pcnt
1781696923	13.88 Volt	210 Pkt	73 Pcnt
1781696623	13.88 Volt	240 Pkt	73 Pcnt
1781696323	13.88 Volt	250 Pkt	74 Pcnt
1781696023	13.88 Volt	240 Pkt	74 Pcnt
1781695723	13.88 Volt	240 Pkt	74 Pcnt
1781695423	14.18 Volt	250 Pkt	75 Pcnt
1781695123	14.25 Volt	250 Pkt	75 Pcnt
1781694823	14.25 Volt	250 Pkt	75 Pcnt
1781694523	14.25 Volt	250 Pkt	74 Pcnt
1781694223	14.25 Volt	250 Pkt	73 Pcnt
1781693923	14.25 Volt	250 Pkt	73 Pcnt
1781693623	14.25 Volt	240 Pkt	72 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)