KD6VPH Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KD6VPH. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1789951334	13.83 Volt	20 Pkt	103 Pcnt
1789949534	13.83 Volt	40 Pkt	100 Pcnt
1789946834	13.83 Volt	50 Pkt	98 Pcnt
1789945934	13.83 Volt	50 Pkt	88 Pcnt
1789945034	13.83 Volt	50 Pkt	76 Pcnt
1789944151	13.83 Volt	60 Pkt	78 Pcnt
1789941434	13.83 Volt	60 Pkt	98 Pcnt
1789940549	13.83 Volt	60 Pkt	98 Pcnt
1789936955	13.9 Volt	40 Pkt	93 Pcnt
1789936043	13.9 Volt	60 Pkt	87 Pcnt
1789935138	13.9 Volt	70 Pkt	80 Pcnt
1789930636	13.83 Volt	40 Pkt	100 Pcnt
1789928835	13.83 Volt	40 Pkt	100 Pcnt
1789927935	13.83 Volt	30 Pkt	102 Pcnt
1789925235	13.83 Volt	30 Pkt	100 Pcnt
1789921635	13.83 Volt	20 Pkt	100 Pcnt
1789920735	13.83 Volt	30 Pkt	100 Pcnt
1789919835	13.83 Volt	30 Pkt	100 Pcnt
1789918035	13.83 Volt	30 Pkt	100 Pcnt
1789916235	13.83 Volt	30 Pkt	103 Pcnt
1789915335	13.83 Volt	30 Pkt	100 Pcnt
1789913535	13.83 Volt	30 Pkt	100 Pcnt
1789912635	13.83 Volt	40 Pkt	100 Pcnt
1789911735	13.83 Volt	40 Pkt	96 Pcnt
1789909936	13.83 Volt	50 Pkt	96 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Eff1h: 0, 1, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)