DO2HN-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO2HN-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1789940898	17.9 C	41.18 %	1026.25 hPa
1789940018	18.2 C	41.1 %	1025.88 hPa
1789936378	19.7 C	40.79 %	1027.13 hPa
1789935474	20 C	40.7 %	1025.75 hPa
1789934570	20.3 C	40.33 %	1024.75 hPa
1789933666	20.6 C	40.13 %	1025.5 hPa
1789932762	20.9 C	40.09 %	1025.63 hPa
1789931858	21.3 C	39.64 %	1026.25 hPa
1789930954	21.8 C	39.25 %	1025.88 hPa
1789929146	22.7 C	38.12 %	1025.25 hPa
1789928244	23.2 C	37.49 %	1024 hPa
1789927338	23.7 C	36.33 %	1023.63 hPa
1789923528	28.9 C	27.95 %	1022.5 hPa
1789923511	28.9 C	27.74 %	1021.5 hPa
1789923479	28.9 C	27.74 %	1021.88 hPa
1789923314	28.8 C	27.72 %	1019 hPa
1789923298	28.8 C	27.72 %	1020 hPa
1789923282	28.8 C	27.72 %	1020 hPa
1789923266	28.8 C	27.69 %	1017.25 hPa
1789923240	28.8 C	27.69 %	1020.25 hPa
1789923208	28.8 C	27.69 %	1020.88 hPa
1789923192	28.8 C	28.22 %	1022.5 hPa
1789923160	28.8 C	28.22 %	1022 hPa
1789923144	28.8 C	28.41 %	1025 hPa
1789923128	28.8 C	28.41 %	1023.63 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)