YO8B-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO8B-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TRX*	Shelter*	Exterior*
1776851466	24.9 °C	7.5 °C	5 °C
1776850865	25.2 °C	9.7 °C	7.3 °C
1776850265	24.2 °C	11.5 °C	8.4 °C
1776849666	23.6 °C	12.6 °C	8.1 °C
1776849066	23.6 °C	11.2 °C	10.1 °C
1776848466	23.5 °C	7.6 °C	9.3 °C
1776847866	23.8 °C	7.1 °C	5.9 °C
1776847266	24.1 °C	8.4 °C	7.2 °C
1776846665	24.3 °C	9.1 °C	8.2 °C
1776846065	24.5 °C	9.3 °C	8.2 °C
1776845466	24.5 °C	10.2 °C	8.6 °C
1776844866	24.2 °C	10.6 °C	9.2 °C
1776844266	24.1 °C	11.3 °C	9.5 °C
1776843666	23.9 °C	12.4 °C	9.5 °C
1776843065	23.5 °C	11.7 °C	10.8 °C
1776842465	23.3 °C	10.4 °C	8.8 °C
1776841866	23.2 °C	9.8 °C	8.9 °C
1776841266	23.2 °C	9.2 °C	8.6 °C
1776840676	23.4 °C	9.1 °C	7.6 °C
1776840066	23.6 °C	8.3 °C	9.2 °C
1776839466	24.1 °C	7.5 °C	8.1 °C
1776838865	24.9 °C	7.4 °C	7.7 °C
1776838267	26.4 °C	7.1 °C	7.2 °C
1776837666	28.1 °C	6.9 °C	7.1 °C
1776837066	21.4 °C	6.9 °C	6.9 °C

*Used Equation Coefficients:

TRX: 0, 1, -100

Shelter: 0, 1, -100

Exterior: 0, 1, -100

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)