YB0X-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB0X-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	TxTraffic*	RxDrop*
1772841418	138 Pkt	204 Pkt	254 Pkt
1772841320	138 Pkt	203 Pkt	254 Pkt
1772841271	138 Pkt	204 Pkt	254 Pkt
1772841221	138 Pkt	204 Pkt	253 Pkt
1772840876	138 Pkt	204 Pkt	254 Pkt
1772840777	138 Pkt	204 Pkt	254 Pkt
1772840728	138 Pkt	203 Pkt	254 Pkt
1772840679	138 Pkt	204 Pkt	254 Pkt
1772840580	139 Pkt	204 Pkt	254 Pkt
1772840546	139 Pkt	203 Pkt	254 Pkt
1772840480	139 Pkt	203 Pkt	254 Pkt
1772840431	138 Pkt	202 Pkt	253 Pkt
1772840349	139 Pkt	202 Pkt	253 Pkt
1772840283	139 Pkt	201 Pkt	254 Pkt
1772837720	139 Pkt	203 Pkt	254 Pkt
1772837622	139 Pkt	204 Pkt	254 Pkt
1772837572	139 Pkt	203 Pkt	1 Pkt
1772837523	139 Pkt	204 Pkt	2 Pkt
1772837474	139 Pkt	204 Pkt	2 Pkt
1772837375	138 Pkt	204 Pkt	1 Pkt
1772837326	139 Pkt	204 Pkt	1 Pkt
1772835109	138 Pkt	203 Pkt	1 Pkt
1772835060	138 Pkt	203 Pkt	1 Pkt
1772835010	138 Pkt	203 Pkt	1 Pkt
1772834764	138 Pkt	204 Pkt	1 Pkt

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)