IZ2URO-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IZ2URO-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	RSSI*	Uptime*
1784702611	20.14 Volt	-63 dBm	5.2 Hours
1784702256	19.76 Volt	-61 dBm	5.1 Hours
1784701901	21.15 Volt	-63 dBm	5 Hours
1784701546	20.03 Volt	-61 dBm	4.9 Hours
1784701191	19.66 Volt	-61 dBm	4.8 Hours
1784700836	19.82 Volt	-61 dBm	4.7 Hours
1784700480	19.92 Volt	-63 dBm	4.6 Hours
1784700125	20.08 Volt	-63 dBm	4.5 Hours
1784699770	20.24 Volt	-63 dBm	4.4 Hours
1784699415	20.08 Volt	-63 dBm	4.3 Hours
1784699059	19.76 Volt	-63 dBm	4.2 Hours
1784698704	19.44 Volt	-61 dBm	4.1 Hours
1784698346	18.8 Volt	-63 dBm	4 Hours
1784697991	18.91 Volt	-61 dBm	3.9 Hours
1784697636	18.96 Volt	-63 dBm	3.8 Hours
1784697281	18.96 Volt	-63 dBm	3.7 Hours
1784696926	18.86 Volt	-63 dBm	3.6 Hours
1784696593	18.86 Volt	-63 dBm	3.5 Hours
1784696216	18.86 Volt	-61 dBm	3.4 Hours
1784695860	18.8 Volt	-63 dBm	3.3 Hours
1784695502	18.8 Volt	-63 dBm	3.2 Hours
1784695147	18.54 Volt	-61 dBm	3.1 Hours
1784694792	18.75 Volt	-63 dBm	3 Hours
1784694437	18.7 Volt	-63 dBm	2.9 Hours
1784694082	18.64 Volt	-63 dBm	2.8 Hours

*Used Equation Coefficients:

Battery: 0, 0.01, 0

RSSI: 0, -1, 0

Uptime: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)