HB9DD-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HB9DD-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1780885244	11.85 Volt	1280 Pkt	15 Pcnt
1780884945	12 Volt	1280 Pkt	14 Pcnt
1780884944	12 Volt	1280 Pkt	14 Pcnt
1780884644	12.08 Volt	1280 Pkt	17 Pcnt
1780884344	12.08 Volt	1280 Pkt	23 Pcnt
1780884044	12.08 Volt	1280 Pkt	22 Pcnt
1780883745	12.08 Volt	1280 Pkt	22 Pcnt
1780883745	12.08 Volt	1280 Pkt	22 Pcnt
1780883444	12.15 Volt	1280 Pkt	20 Pcnt
1780883145	12.15 Volt	1280 Pkt	22 Pcnt
1780882845	12.15 Volt	1280 Pkt	23 Pcnt
1780882545	12.15 Volt	1280 Pkt	25 Pcnt
1780882545	12.15 Volt	1280 Pkt	25 Pcnt
1780882245	12.15 Volt	1280 Pkt	25 Pcnt
1780881944	12.15 Volt	1280 Pkt	30 Pcnt
1780881645	12.15 Volt	1280 Pkt	33 Pcnt
1780881345	12.15 Volt	1280 Pkt	32 Pcnt
1780881345	12.15 Volt	1280 Pkt	32 Pcnt
1780881045	12.15 Volt	1280 Pkt	29 Pcnt
1780880745	12.15 Volt	1280 Pkt	29 Pcnt
1780880745	12.15 Volt	1280 Pkt	29 Pcnt
1780880445	12.15 Volt	1280 Pkt	31 Pcnt
1780880145	12.23 Volt	1280 Pkt	32 Pcnt
1780880145	12.23 Volt	1280 Pkt	32 Pcnt
1780879845	12.23 Volt	1280 Pkt	36 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)