EC2UT-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EC2UT-8. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1789926592	30.1 C	28.53 %	1033.75 hPa
1789925671	30.2 C	27.08 %	1023.38 hPa
1789919705	37.6 C	14.05 %	1027.63 hPa
1789919458	38.3 C	14.12 %	1026.38 hPa
1789918997	38.6 C	14.01 %	1025.5 hPa
1789918693	38.6 C	14.91 %	1019.25 hPa
1789903108	33.4 C	22.06 %	0 hPa
1789902364	34.4 C	21.89 %	1033 hPa
1789897753	28.5 C	27.43 %	0 hPa
1789897546	28.5 C	27.57 %	0 hPa
1789896494	28.9 C	28.48 %	1029.5 hPa
1789896110	27.3 C	29.84 %	0 hPa
1789895809	26.8 C	30.84 %	0 hPa
1789895477	26.2 C	32.64 %	0 hPa
1789895210	24.8 C	35.5 %	0 hPa
1789894712	23.4 C	36.61 %	0 hPa
1789886785	21.7 C	37.49 %	900.25 hPa
1789858444	25.5 C	32.4 %	898.63 hPa
1789751751	40.8 C	18.06 %	1028.63 hPa
1789742721	43.8 C	19.26 %	1028.63 hPa
1789738096	31.4 C	24.03 %	1028.5 hPa
1789737027	34.2 C	21.74 %	1028.38 hPa
1789734440	39.1 C	23.77 %	1029.63 hPa
1789727143	35.9 C	21.16 %	1031.88 hPa
1789726891	36.2 C	21.35 %	1027.88 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)