DB0EMS-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0EMS-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U1*	U2*	Temp*
1789951191	13.2 Volt	13.6 Volt	23 C
1789950891	13.2 Volt	13.6 Volt	23.5 C
1789950591	13.2 Volt	13.6 Volt	23 C
1789950291	13.2 Volt	13.6 Volt	23 C
1789949990	13.2 Volt	13.6 Volt	23 C
1789949690	13.2 Volt	13.6 Volt	23 C
1789949390	13.2 Volt	13.6 Volt	23 C
1789949089	13.2 Volt	13.6 Volt	23 C
1789948789	13.2 Volt	13.6 Volt	23 C
1789948489	13.2 Volt	13.6 Volt	23 C
1789948189	13.2 Volt	13.6 Volt	23 C
1789947888	13.2 Volt	13.6 Volt	23 C
1789947588	13.2 Volt	13.6 Volt	23 C
1789947288	13.2 Volt	13.6 Volt	23 C
1789946987	13.2 Volt	13.6 Volt	23 C
1789946687	13.2 Volt	13.6 Volt	23 C
1789946387	13.2 Volt	13.6 Volt	23 C
1789946087	13.2 Volt	13.6 Volt	23 C
1789945786	13.2 Volt	13.6 Volt	23 C
1789945486	13.2 Volt	13.6 Volt	23 C
1789945186	13.2 Volt	13.6 Volt	23 C
1789944885	13.2 Volt	13.6 Volt	23 C
1789944585	13.2 Volt	13.6 Volt	23 C
1789944285	13.2 Volt	13.6 Volt	23 C
1789943985	13.2 Volt	13.6 Volt	23 C

*Used Equation Coefficients:

U1: 0, 0.1, 0

U2: 0, 0.1, 0

Temp: 0, 0.5, -64

Vin: 0, 0.079, 0

I2: 0, 19.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)