F1ZUI-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F1ZUI-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Tint*	RHint*	Lum.*	Vent*
1788612611	33.58 C	45 %	90 %	10 kmh
1788611997	33.52 C	45 %	90 %	12 kmh
1788611384	33.39 C	45 %	90 %	5 kmh
1788610770	33.3 C	45 %	89 %	0 kmh
1788610156	33.25 C	46 %	89 %	10 kmh
1788609543	33.26 C	46 %	89 %	12 kmh
1788608316	32.7 C	46 %	89 %	6 kmh
1788607702	32.27 C	47 %	90 %	13 kmh
1788607088	31.83 C	47 %	90 %	11 kmh
1788606475	31.43 C	47 %	90 %	13 kmh
1788605861	31.07 C	47 %	90 %	0 kmh
1788605247	30.86 C	48 %	91 %	9 kmh
1788604634	30.84 C	48 %	88 %	15 kmh
1788604020	30.86 C	48 %	88 %	8 kmh
1788603406	30.85 C	48 %	87 %	6 kmh
1788602793	30.78 C	48 %	88 %	11 kmh
1788602179	30.44 C	48 %	87 %	10 kmh
1788601566	29.98 C	48 %	88 %	0 kmh
1788600952	29.4 C	49 %	91 %	8 kmh
1788600338	28.87 C	49 %	89 %	5 kmh
1788599726	28.41 C	49 %	88 %	8 kmh
1788599111	27.95 C	49 %	90 %	13 kmh
1788597270	26.11 C	51 %	89 %	0 kmh
1788596657	25.66 C	51 %	89 %	6 kmh
1788595430	25.02 C	52 %	87 %	8 kmh

*Used Equation Coefficients:

Tint: 0, 1, 0

RHint: 0, 1, 0

Lum.: 0, 1, 0

Vent: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)