YU0XKS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YU0XKS-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1765532772	12.38 Volt	40 Pkt	88 Pcnt
1765532172	12.38 Volt	40 Pkt	87 Pcnt
1765531572	12.38 Volt	40 Pkt	86 Pcnt
1765530972	12.38 Volt	40 Pkt	89 Pcnt
1765530372	12.38 Volt	40 Pkt	87 Pcnt
1765529772	12.38 Volt	40 Pkt	87 Pcnt
1765529172	12.38 Volt	40 Pkt	85 Pcnt
1765527973	12.38 Volt	40 Pkt	82 Pcnt
1765527372	12.38 Volt	40 Pkt	83 Pcnt
1765526772	12.38 Volt	40 Pkt	83 Pcnt
1765526172	12.38 Volt	40 Pkt	83 Pcnt
1765525572	12.38 Volt	40 Pkt	83 Pcnt
1765524972	12.38 Volt	40 Pkt	87 Pcnt
1765524372	12.38 Volt	40 Pkt	87 Pcnt
1765523772	12.38 Volt	50 Pkt	85 Pcnt
1765523173	12.38 Volt	50 Pkt	82 Pcnt
1765522573	12.38 Volt	50 Pkt	80 Pcnt
1765521973	12.38 Volt	50 Pkt	78 Pcnt
1765521373	12.38 Volt	50 Pkt	79 Pcnt
1765520794	12.38 Volt	60 Pkt	81 Pcnt
1765520173	12.38 Volt	60 Pkt	82 Pcnt
1765519573	12.38 Volt	60 Pkt	91 Pcnt
1765518973	12.38 Volt	60 Pkt	90 Pcnt
1765518373	12.38 Volt	60 Pkt	91 Pcnt
1765517774	12.38 Volt	60 Pkt	91 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)