OE6XDG-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE6XDG-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1755097809	22.9 deg C	64.6 %	1170.3 hPa
1755096009	22.9 deg C	64.9 %	1170.3 hPa
1755095109	22.9 deg C	65 %	1170.3 hPa
1755094209	22.9 deg C	65 %	1170.5 hPa
1755093372	22.8 deg C	65 %	1170.6 hPa
1755092409	22.8 deg C	65 %	1170.7 hPa
1755091508	22.7 deg C	65.3 %	1170.9 hPa
1755090278	22.6 deg C	66.5 %	1171.3 hPa
1755088477	22.5 deg C	66.7 %	1171.7 hPa
1755086677	22.5 deg C	66.6 %	1172.1 hPa
1755085777	22.5 deg C	66.5 %	1172.3 hPa
1755084877	22.4 deg C	66.4 %	1172.5 hPa
1755083977	22.4 deg C	66.6 %	1172.5 hPa
1755083077	22.4 deg C	66.5 %	1172.7 hPa
1755082177	22.4 deg C	66.5 %	1173 hPa
1755081277	22.3 deg C	66.3 %	1173.2 hPa
1755080377	22.3 deg C	66.5 %	1173.3 hPa
1755079477	22.3 deg C	66.2 %	1173.5 hPa
1755078577	22.3 deg C	66.5 %	1173.6 hPa
1755078244	22.3 deg C	66.4 %	1173.7 hPa
1755077344	22.2 deg C	66.3 %	1173.9 hPa
1755076444	22.2 deg C	66.3 %	1174 hPa
1755075544	22.1 deg C	66.1 %	1174 hPa
1755074644	22.1 deg C	65.9 %	1174.2 hPa
1755073744	22 deg C	65.7 %	1174.3 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)