ON4BCY-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ON4BCY-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784686151	11.93 Volt	1280 Pkt	100 Pcnt
1784685850	12 Volt	1280 Pkt	100 Pcnt
1784685550	11.93 Volt	1280 Pkt	100 Pcnt
1784685250	12 Volt	1280 Pkt	100 Pcnt
1784684951	11.93 Volt	1280 Pkt	100 Pcnt
1784684652	12 Volt	1280 Pkt	100 Pcnt
1784684350	11.93 Volt	1280 Pkt	100 Pcnt
1784684052	12 Volt	1280 Pkt	100 Pcnt
1784683751	12 Volt	1280 Pkt	100 Pcnt
1784683450	11.93 Volt	1280 Pkt	100 Pcnt
1784683151	12 Volt	1280 Pkt	100 Pcnt
1784682850	11.93 Volt	1280 Pkt	100 Pcnt
1784682552	11.93 Volt	1280 Pkt	100 Pcnt
1784682250	11.93 Volt	1280 Pkt	100 Pcnt
1784681950	12 Volt	1280 Pkt	100 Pcnt
1784681651	12 Volt	1280 Pkt	100 Pcnt
1784681350	11.93 Volt	1280 Pkt	100 Pcnt
1784681050	11.93 Volt	1280 Pkt	100 Pcnt
1784680752	11.93 Volt	1280 Pkt	100 Pcnt
1784680450	12 Volt	1280 Pkt	100 Pcnt
1784680151	11.93 Volt	1280 Pkt	100 Pcnt
1784679850	12 Volt	1280 Pkt	100 Pcnt
1784679552	12 Volt	1280 Pkt	100 Pcnt
1784679250	12 Volt	1280 Pkt	100 Pcnt
1784678950	12 Volt	1280 Pkt	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)