CASCTY Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CASCTY. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1784675102	12.45 Volt	420 Pkt	170 Pkt	53 Pcnt
1784674802	12.45 Volt	450 Pkt	180 Pkt	53 Pcnt
1784674529	12.45 Volt	450 Pkt	180 Pkt	54 Pcnt
1784674202	12.45 Volt	430 Pkt	170 Pkt	52 Pcnt
1784673902	12.45 Volt	410 Pkt	170 Pkt	53 Pcnt
1784673602	12.45 Volt	390 Pkt	160 Pkt	54 Pcnt
1784673302	12.45 Volt	390 Pkt	160 Pkt	53 Pcnt
1784673002	12.45 Volt	380 Pkt	150 Pkt	53 Pcnt
1784672702	12.45 Volt	390 Pkt	150 Pkt	52 Pcnt
1784672402	12.45 Volt	390 Pkt	150 Pkt	53 Pcnt
1784672102	12.45 Volt	400 Pkt	150 Pkt	53 Pcnt
1784671802	12.45 Volt	390 Pkt	150 Pkt	52 Pcnt
1784671502	12.45 Volt	410 Pkt	170 Pkt	53 Pcnt
1784671202	12.45 Volt	390 Pkt	150 Pkt	53 Pcnt
1784670902	12.45 Volt	380 Pkt	160 Pkt	53 Pcnt
1784670602	12.45 Volt	410 Pkt	160 Pkt	55 Pcnt
1784670302	12.45 Volt	420 Pkt	160 Pkt	55 Pcnt
1784670002	12.45 Volt	450 Pkt	170 Pkt	56 Pcnt
1784669702	12.45 Volt	440 Pkt	170 Pkt	55 Pcnt
1784669402	12.45 Volt	450 Pkt	170 Pkt	56 Pcnt
1784669102	12.45 Volt	440 Pkt	170 Pkt	56 Pcnt
1784668802	12.45 Volt	440 Pkt	160 Pkt	55 Pcnt
1784668502	12.45 Volt	430 Pkt	150 Pkt	55 Pcnt
1784668202	12.45 Volt	430 Pkt	150 Pkt	55 Pcnt
1784667902	12.45 Volt	420 Pkt	140 Pkt	55 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)