BX6ABV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX6ABV-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1787583282	35.7 C	6 p	18 p	736 p
1787582081	40.5 C	6 p	25 p	736 p
1787580881	34 C	6 p	25 p	736 p
1787579681	34 C	13 p	25 p	735 p
1787578481	34.5 C	6 p	18 p	728 p
1787577281	40.2 C	6 p	19 p	728 p
1787576082	35.5 C	6 p	19 p	727 p
1787574882	38.3 C	7 p	19 p	726 p
1787573682	41.3 C	6 p	18 p	724 p
1787572481	41.2 C	6 p	18 p	723 p
1787571281	40.6 C	6 p	18 p	723 p
1787570081	41.9 C	6 p	18 p	723 p
1787568881	41.2 C	6 p	18 p	722 p
1787567681	41.9 C	6 p	18 p	722 p
1787566482	41.5 C	6 p	18 p	722 p
1787565282	41.9 C	6 p	18 p	722 p
1787564081	41.3 C	6 p	19 p	722 p
1787562881	41.1 C	6 p	20 p	722 p
1787561805	40.9 C	7 p	20 p	725 p
1787560481	41.8 C	7 p	21 p	737 p
1787559282	41.9 C	6 p	22 p	741 p
1787558082	41.2 C	8 p	22 p	747 p
1787556882	41.5 C	8 p	23 p	749 p
1787555682	40.6 C	6 p	23 p	755 p
1787554482	41.9 C	9 p	26 p	762 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)