OE3OSB Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3OSB. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	T@Dach*	T@SDR*
1776883925	13.05 Volt	17 C	17.5 C
1776883625	13.05 Volt	17 C	17.5 C
1776883325	13.05 Volt	17 C	17.5 C
1776883025	13.05 Volt	17 C	17.5 C
1776882725	13.05 Volt	17 C	17.5 C
1776882425	13.05 Volt	17 C	17.5 C
1776882125	13.05 Volt	17 C	17.5 C
1776881825	13.05 Volt	17 C	17.5 C
1776881525	13.05 Volt	17 C	17.5 C
1776881225	13.05 Volt	17 C	17.5 C
1776880926	13.05 Volt	17 C	17.5 C
1776880625	13.05 Volt	17 C	17.5 C
1776880325	13.05 Volt	17 C	17.5 C
1776880026	13.05 Volt	17 C	17.5 C
1776879725	13.05 Volt	17 C	17.5 C
1776879426	13.05 Volt	17 C	18 C
1776879126	13.05 Volt	17 C	18 C
1776878826	13.05 Volt	17 C	18 C
1776878526	13.05 Volt	17 C	18 C
1776878226	13.05 Volt	17 C	18 C
1776877926	13.05 Volt	17 C	18 C
1776877626	13.05 Volt	17 C	18 C
1776877326	13.05 Volt	17 C	18 C
1776877026	13.05 Volt	17 C	18 C
1776876726	13.05 Volt	17 C	18 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

T@Dach: 0, 0.5, -64

T@SDR: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)