SQ8MAE-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ8MAE-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Eff*
1784727814	13.8 Volt	100 Pcnt	78 Pcnt
1784700789	13.8 Volt	100 Pcnt	100 Pcnt
1784695384	13.8 Volt	100 Pcnt	100 Pcnt
1784694783	13.8 Volt	100 Pcnt	100 Pcnt
1784693582	13.8 Volt	100 Pcnt	100 Pcnt
1784684574	13.8 Volt	100 Pcnt	100 Pcnt
1784683973	13.8 Volt	100 Pcnt	100 Pcnt
1784682772	13.8 Volt	100 Pcnt	100 Pcnt
1784681571	13.8 Volt	100 Pcnt	100 Pcnt
1784680370	13.8 Volt	100 Pcnt	100 Pcnt
1784679169	13.8 Volt	100 Pcnt	100 Pcnt
1784677967	13.8 Volt	100 Pcnt	100 Pcnt
1784677367	13.8 Volt	100 Pcnt	100 Pcnt
1784671962	13.8 Volt	100 Pcnt	100 Pcnt
1784671361	13.8 Volt	100 Pcnt	100 Pcnt
1784613420	13.8 Volt	100 Pcnt	83 Pcnt
1784594802	13.8 Volt	100 Pcnt	83 Pcnt
1784591199	13.8 Volt	100 Pcnt	83 Pcnt
1784588196	13.8 Volt	100 Pcnt	83 Pcnt
1784585193	13.8 Volt	100 Pcnt	83 Pcnt
1784563573	13.65 Volt	100 Pcnt	82 Pcnt
1784553363	13.8 Volt	100 Pcnt	82 Pcnt
1784548559	13.8 Volt	100 Pcnt	82 Pcnt
1784547958	13.8 Volt	100 Pcnt	82 Pcnt
1784520332	13.8 Volt	100 Pcnt	82 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Eff1h: 0, 1, 0

Eff: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)