DB0KR-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0KR-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1789960234	15.3 deg C	52.1 %	1028.4 hPa
1789959333	15.3 deg C	52.1 %	1028.5 hPa
1789958433	15.4 deg C	52 %	1028.5 hPa
1789957533	15.6 deg C	51.9 %	1028.4 hPa
1789956633	15.8 deg C	51.5 %	1028.4 hPa
1789955733	16 deg C	51.1 %	1028.4 hPa
1789954833	16.1 deg C	51.1 %	1028.4 hPa
1789953933	16.2 deg C	51.1 %	1028.4 hPa
1789953033	16.3 deg C	51 %	1028.4 hPa
1789952133	16.4 deg C	51 %	1028.6 hPa
1789951246	16.4 deg C	51 %	1028.6 hPa
1789950333	16.6 deg C	51 %	1028.6 hPa
1789949452	16.7 deg C	51 %	1028.4 hPa
1789948532	16.8 deg C	51.1 %	1028.4 hPa
1789947632	16.8 deg C	51.1 %	1028.3 hPa
1789946732	16.9 deg C	51.1 %	1028.4 hPa
1789945832	17 deg C	51.1 %	1028.2 hPa
1789944932	17.1 deg C	51.1 %	1028 hPa
1789944032	17.2 deg C	51.2 %	1027.7 hPa
1789943132	17.3 deg C	51.1 %	1027.6 hPa
1789942232	17.4 deg C	51.1 %	1027.6 hPa
1789941332	17.6 deg C	51 %	1027.4 hPa
1789940432	17.8 deg C	51 %	1027.2 hPa
1789939532	17.9 deg C	51.1 %	1027.2 hPa
1789938631	18.1 deg C	51.1 %	1027 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)