DM2OV-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DM2OV-14. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1776657145	25.8 deg C	45 %	1013.2 hPa
1776656245	25.8 deg C	45 %	1013.3 hPa
1776655281	25.9 deg C	45 %	1013.5 hPa
1776654381	25.9 deg C	45 %	1013.6 hPa
1776653909	26 deg C	45 %	1013.5 hPa
1776653627	26 deg C	45 %	1013.6 hPa
1776653547	26 deg C	45 %	1013.6 hPa
1776653376	26 deg C	45 %	1013.6 hPa
1776653133	26 deg C	45 %	1013.6 hPa
1776653004	26 deg C	45 %	1013.6 hPa
1776652771	26 deg C	45 %	1013.6 hPa
1776652603	26.1 deg C	45 %	1013.6 hPa
1776652462	26 deg C	45 %	1013.6 hPa
1776652253	26.1 deg C	45.1 %	1013.7 hPa
1776652100	26.1 deg C	45 %	1013.6 hPa
1776651805	26.1 deg C	45 %	1013.7 hPa
1776651741	26.1 deg C	45 %	1013.7 hPa
1776651569	26.1 deg C	45 %	1013.7 hPa
1776651397	26.1 deg C	45 %	1013.7 hPa
1776651329	26.1 deg C	45.1 %	1013.7 hPa
1776651182	26.1 deg C	45.1 %	1013.7 hPa
1776650661	26.2 deg C	45 %	1013.8 hPa
1776650612	26.2 deg C	45 %	1013.8 hPa
1776650486	26.2 deg C	45 %	1013.8 hPa
1776650302	26.2 deg C	45.1 %	1013.8 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)