W5IPA-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W5IPA-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1784673091	14.1 Volt	100 Pkt	10 Pkt	100 Pcnt
1784672491	14.1 Volt	100 Pkt	10 Pkt	100 Pcnt
1784671891	14.1 Volt	100 Pkt	10 Pkt	100 Pcnt
1784671291	14.1 Volt	110 Pkt	10 Pkt	100 Pcnt
1784670691	14.1 Volt	110 Pkt	20 Pkt	100 Pcnt
1784670092	14.1 Volt	100 Pkt	20 Pkt	100 Pcnt
1784670091	14.1 Volt	100 Pkt	20 Pkt	100 Pcnt
1784669491	14.1 Volt	100 Pkt	10 Pkt	100 Pcnt
1784668891	14.1 Volt	100 Pkt	10 Pkt	100 Pcnt
1784668291	14.1 Volt	90 Pkt	10 Pkt	100 Pcnt
1784667691	14.1 Volt	110 Pkt	10 Pkt	100 Pcnt
1784667091	14.1 Volt	110 Pkt	10 Pkt	100 Pcnt
1784666492	14.18 Volt	110 Pkt	20 Pkt	100 Pcnt
1784666491	14.18 Volt	110 Pkt	20 Pkt	100 Pcnt
1784665891	14.1 Volt	130 Pkt	20 Pkt	100 Pcnt
1784665291	14.1 Volt	140 Pkt	30 Pkt	100 Pcnt
1784664691	14.1 Volt	140 Pkt	30 Pkt	100 Pcnt
1784664091	14.1 Volt	160 Pkt	40 Pkt	100 Pcnt
1784663491	14.1 Volt	180 Pkt	40 Pkt	100 Pcnt
1784662891	14.1 Volt	180 Pkt	40 Pkt	100 Pcnt
1784662291	14.18 Volt	180 Pkt	40 Pkt	100 Pcnt
1784661691	14.18 Volt	180 Pkt	40 Pkt	100 Pcnt
1784661093	14.1 Volt	180 Pkt	50 Pkt	100 Pcnt
1784661091	14.1 Volt	180 Pkt	50 Pkt	100 Pcnt
1784660491	14.1 Volt	170 Pkt	50 Pkt	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

TEMP: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)