DL5NBU-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL5NBU-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1787581940	25.6 deg C	33.6 %	1017.5 hPa
1787581040	25.1 deg C	34.6 %	1017.9 hPa
1787580707	25.5 deg C	33.6 %	1017.9 hPa
1787579807	26.8 deg C	34.1 %	1017.9 hPa
1787578907	26.5 deg C	32.1 %	1018 hPa
1787578007	26.8 deg C	32.7 %	1018.2 hPa
1787577107	26.9 deg C	32.9 %	1018.5 hPa
1787576207	25.3 deg C	32.4 %	1018.7 hPa
1787575306	25.6 deg C	35 %	1019 hPa
1787574406	25 deg C	34.6 %	1019.2 hPa
1787573506	24.4 deg C	37.8 %	1019.2 hPa
1787572606	23.4 deg C	37.8 %	1019.5 hPa
1787571706	23.2 deg C	40.3 %	1019.6 hPa
1787570862	22.7 deg C	41.1 %	1019.7 hPa
1787569906	21.8 deg C	42.2 %	1020.1 hPa
1787569006	20.5 deg C	44.8 %	1020.4 hPa
1787568676	20 deg C	45 %	1020.5 hPa
1787567776	19.5 deg C	44.7 %	1020.7 hPa
1787566876	19.7 deg C	46.6 %	1020.8 hPa
1787565976	19.8 deg C	46.7 %	1021.1 hPa
1787565076	19.7 deg C	46.4 %	1021.2 hPa
1787564176	19.9 deg C	49.2 %	1021.4 hPa
1787563277	19.7 deg C	50.3 %	1021.5 hPa
1787562376	19.2 deg C	52.2 %	1021.7 hPa
1787561476	18.9 deg C	53 %	1021.8 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)