ZS0PMB-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ZS0PMB-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1777896193	13.62 Volt	10 Pkt	100 Pcnt
1777894391	13.54 Volt	10 Pkt	100 Pcnt
1777892589	13.54 Volt	10 Pkt	100 Pcnt
1777890788	13.54 Volt	10 Pkt	100 Pcnt
1777888986	13.62 Volt	10 Pkt	100 Pcnt
1777887184	13.54 Volt	10 Pkt	100 Pcnt
1777885382	14.15 Volt	10 Pkt	100 Pcnt
1777883581	14.15 Volt	10 Pkt	100 Pcnt
1777881779	13.62 Volt	10 Pkt	100 Pcnt
1777879977	13.46 Volt	10 Pkt	100 Pcnt
1777878175	13.39 Volt	10 Pkt	100 Pcnt
1777876374	13.31 Volt	10 Pkt	100 Pcnt
1777874572	13.23 Volt	10 Pkt	100 Pcnt
1777872770	13.01 Volt	10 Pkt	100 Pcnt
1777870968	12.93 Volt	10 Pkt	100 Pcnt
1777869166	12.93 Volt	10 Pkt	100 Pcnt
1777867365	12.93 Volt	10 Pkt	100 Pcnt
1777831329	13.08 Volt	10 Pkt	100 Pcnt
1777829528	13.08 Volt	10 Pkt	100 Pcnt
1777827726	13.08 Volt	10 Pkt	100 Pcnt
1777825924	13.08 Volt	10 Pkt	100 Pcnt
1777824122	13.08 Volt	10 Pkt	100 Pcnt
1777822321	13.08 Volt	10 Pkt	100 Pcnt
1777820519	13.16 Volt	10 Pkt	100 Pcnt
1777818717	13.39 Volt	10 Pkt	100 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.0765, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)