S55UJE-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object S55UJE-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Uacu*	Iacu*	Temp*	Rx1h*
1787591031	13.71 Volt	3.13 A	18.5 C	250 Pkt
1787591030	13.71 Volt	3.13 A	18.5 C	250 Pkt
1787590730	13.71 Volt	3.53 A	18.5 C	240 Pkt
1787590730	13.71 Volt	3.53 A	18.5 C	240 Pkt
1787590430	13.71 Volt	3.13 A	18.5 C	240 Pkt
1787590429	13.71 Volt	3.13 A	18.5 C	240 Pkt
1787590130	13.71 Volt	3.13 A	18.5 C	220 Pkt
1787590129	13.71 Volt	3.13 A	18.5 C	220 Pkt
1787589830	13.71 Volt	3.53 A	19 C	220 Pkt
1787589829	13.71 Volt	3.53 A	19 C	220 Pkt
1787589529	13.71 Volt	3.53 A	19 C	220 Pkt
1787589529	13.71 Volt	3.53 A	19 C	220 Pkt
1787589229	13.71 Volt	3.13 A	19 C	220 Pkt
1787589228	13.71 Volt	3.13 A	19 C	220 Pkt
1787588929	13.61 Volt	2.35 A	19.5 C	210 Pkt
1787588928	13.61 Volt	2.35 A	19.5 C	210 Pkt
1787588628	13.71 Volt	3.53 A	19.5 C	210 Pkt
1787588628	13.71 Volt	3.53 A	19.5 C	210 Pkt
1787588328	13.71 Volt	3.13 A	19.5 C	210 Pkt
1787588327	13.71 Volt	3.13 A	19.5 C	210 Pkt
1787588028	13.61 Volt	2.74 A	20 C	220 Pkt
1787588027	13.61 Volt	2.74 A	20 C	220 Pkt
1787587728	13.61 Volt	2.74 A	20 C	210 Pkt
1787587727	13.61 Volt	2.74 A	20 C	210 Pkt
1787587427	13.71 Volt	3.53 A	20 C	210 Pkt

*Used Equation Coefficients:

Uacu: 0, 0.100819, 0

Iacu: 0, 0.3917, -49.7457

Temp: 0, 0.5, -64

Rx1h: 0, 10, 0

WIND: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)