SR8WXB-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8WXB-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Tempre*
1784716934	2 Pkt	2 Pkt	40.5 DegC
1784715731	5 Pkt	2 Pkt	40.5 DegC
1784715131	3 Pkt	4 Pkt	40.5 DegC
1784714525	2 Pkt	2 Pkt	40.5 DegC
1784713925	1 Pkt	3 Pkt	40.5 DegC
1784713322	10 Pkt	2 Pkt	40.5 DegC
1784712722	1 Pkt	3 Pkt	40.5 DegC
1784712119	2 Pkt	2 Pkt	40.5 DegC
1784711519	4 Pkt	3 Pkt	40.5 DegC
1784710917	4 Pkt	6 Pkt	40 DegC
1784710305	2 Pkt	3 Pkt	40 DegC
1784709702	2 Pkt	2 Pkt	40 DegC
1784709102	1 Pkt	3 Pkt	40 DegC
1784708500	1 Pkt	2 Pkt	40 DegC
1784707900	2 Pkt	3 Pkt	40 DegC
1784707296	1 Pkt	3 Pkt	40 DegC
1784706693	5 Pkt	3 Pkt	40 DegC
1784706090	3 Pkt	2 Pkt	40 DegC
1784705491	2 Pkt	3 Pkt	40 DegC
1784704888	3 Pkt	2 Pkt	40 DegC
1784704288	1 Pkt	3 Pkt	40 DegC
1784703685	1 Pkt	2 Pkt	40 DegC
1784703085	2 Pkt	3 Pkt	40 DegC
1784702482	2 Pkt	2 Pkt	40 DegC
1784701882	1 Pkt	3 Pkt	40 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)