SR8WXO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8WXO. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1789969771	122 Pkt	9 Pkt	7 Pkt
1789969168	117 Pkt	10 Pkt	8 Pkt
1789968566	94 Pkt	8 Pkt	6 Pkt
1789967963	78 Pkt	8 Pkt	3 Pkt
1789967353	98 Pkt	3 Pkt	1 Pkt
1789966750	72 Pkt	3 Pkt	1 Pkt
1789966147	85 Pkt	3 Pkt	1 Pkt
1789965544	102 Pkt	8 Pkt	2 Pkt
1789964934	92 Pkt	5 Pkt	3 Pkt
1789964332	100 Pkt	7 Pkt	5 Pkt
1789963729	92 Pkt	6 Pkt	4 Pkt
1789963126	82 Pkt	9 Pkt	3 Pkt
1789962516	93 Pkt	10 Pkt	8 Pkt
1789961913	98 Pkt	12 Pkt	10 Pkt
1789961321	87 Pkt	6 Pkt	4 Pkt
1789960708	75 Pkt	9 Pkt	3 Pkt
1789960098	80 Pkt	4 Pkt	2 Pkt
1789959495	97 Pkt	12 Pkt	10 Pkt
1789958892	152 Pkt	24 Pkt	22 Pkt
1789958289	117 Pkt	14 Pkt	8 Pkt
1789957680	144 Pkt	11 Pkt	9 Pkt
1789957077	148 Pkt	15 Pkt	13 Pkt
1789956474	73 Pkt	4 Pkt	2 Pkt
1789955871	83 Pkt	9 Pkt	3 Pkt
1789955262	105 Pkt	4 Pkt	2 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.25, -25

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)