VA7LKM-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VA7LKM-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	V input*	Sol A*
1789946541	20.5 C	13.9 Volt	0.2 mA
1789867377	22 C	13.2 Volt	0.2 mA
1789866693	24 C	13.9 Volt	0.2 mA
1789851162	22.5 C	13.9 Volt	0.2 mA
1789831342	10.5 C	12.4 Volt	0 mA
1789829540	10 C	12.4 Volt	0 mA
1789827745	9.5 C	12.3 Volt	0 mA
1789826838	9 C	12.3 Volt	0 mA
1789785817	17.5 C	12.6 Volt	0.2 mA
1789784014	19.5 C	12.8 Volt	0.2 mA
1789782213	21.5 C	13.4 Volt	0.2 mA
1789767801	27.5 C	13.8 Volt	0.2 mA
1789765999	27.5 C	13.9 Volt	0.2 mA
1789764197	28 C	13.9 Volt	0.2 mA
1789760627	29 C	13.9 Volt	0.2 mA
1789747980	21.5 C	13.6 Volt	0.2 mA
1789746179	20 C	12.7 Volt	0.2 mA
1789744376	16.5 C	12.5 Volt	0.2 mA
1789742574	13 C	12.4 Volt	0.2 mA
1789739872	8.5 C	12.4 Volt	0 mA
1789699358	24 C	12.6 Volt	0.2 mA
1789697555	27.5 C	13.1 Volt	0.2 mA
1789661521	23 C	13.2 Volt	0.2 mA
1789659719	21 C	12.6 Volt	0.2 mA
1789656115	13 C	12.4 Volt	0.2 mA

*Used Equation Coefficients:

Temp: 0, 0.5, -62

V input: 0, 0.1, 0

CDS : 0, 0.1, 0

Sol A: 0, 0.1953, -24.803

U2: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)