TB4DSC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TB4DSC-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Decd %*	Value4*	Value5*
1772694532	181 Volt	128 C	64 Pkt	0	0
1772693636	181 Volt	128 C	68 Pkt	0	0
1772693631	181 Volt	128 C	68 Pkt	0	0
1772692739	181 Volt	128 C	74 Pkt	0	0
1772691830	181 Volt	128 C	88 Pkt	0	0
1772691234	181 Volt	128 C	95 Pkt	0	0
1772690929	181 Volt	128 C	97 Pkt	0	0
1772690028	181 Volt	128 C	100 Pkt	0	0
1772689127	181 Volt	128 C	100 Pkt	0	0
1772688226	181 Volt	128 C	86 Pkt	0	0
1772687325	181 Volt	128 C	80 Pkt	0	0
1772686464	-	-	-	-	-
1772686429	181 Volt	128 C	82 Pkt	0	0
1772686424	181 Volt	128 C	82 Pkt	0	0
1772685523	181 Volt	128 C	79 Pkt	0	0
1772685228	181 Volt	128 C	79 Pkt	0	0
1772684622	181 Volt	128 C	79 Pkt	0	0
1772684024	181 Volt	128 C	82 Pkt	0	0
1772683722	181 Volt	128 C	81 Pkt	0	0
1772682825	181 Volt	128 C	78 Pkt	0	0
1772682821	181 Volt	128 C	78 Pkt	0	0
1772681920	181 Volt	128 C	73 Pkt	0	0
1772681622	182 Volt	128 C	76 Pkt	0	0
1772681019	181 Volt	128 C	77 Pkt	0	0
1772680421	181 Volt	128 C	77 Pkt	0	0

*Used Equation Coefficients:

Vin: 0, 1, 0

Temp: 0, 1, 0

Decd %: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)