YO3KXL-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3KXL-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	T_ext*	T_int*	T_rad*
1784661675	27.4 C	30.6 C	37.9 C
1784661078	27.4 C	30.7 C	37.9 C
1784660475	27.6 C	30.9 C	39.2 C
1784659875	27.7 C	31.1 C	37.8 C
1784659277	27.9 C	31.1 C	38.1 C
1784658675	28 C	31.3 C	38.4 C
1784658075	28.2 C	31.4 C	38.8 C
1784657478	28.2 C	31.4 C	39.4 C
1784656875	28.4 C	31.6 C	41.2 C
1784656275	28.6 C	31.8 C	38.2 C
1784655677	28.9 C	31.9 C	38.2 C
1784655075	29 C	32.1 C	38.1 C
1784654475	29.1 C	32 C	37.8 C
1784653878	29.1 C	31.6 C	37.6 C
1784653275	29.5 C	30.9 C	40.2 C
1784652675	30 C	33.6 C	40.1 C
1784652077	30.4 C	33.7 C	38.9 C
1784651475	30.6 C	33.5 C	38.3 C
1784650875	30.3 C	33 C	37.8 C
1784650278	31.1 C	31.8 C	36.4 C
1784649675	31 C	34.1 C	42.2 C
1784649075	30.9 C	34.4 C	39.8 C
1784648478	31.8 C	34.5 C	39.6 C
1784647875	31.4 C	34 C	38.1 C
1784647275	31.8 C	32.2 C	36.1 C

*Used Equation Coefficients:

T_ext: 0, 1, -100

T_int: 0, 1, -100

T_rad: 0, 1, -100

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)