IK8CVE-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IK8CVE-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1780548791	12.68 Volt	0 Pkt	81 Pcnt
1780547591	12.68 Volt	0 Pkt	100 Pcnt
1780546391	12.68 Volt	0 Pkt	100 Pcnt
1780545191	12.68 Volt	0 Pkt	100 Pcnt
1780543991	12.68 Volt	10 Pkt	100 Pcnt
1780542791	12.68 Volt	10 Pkt	100 Pcnt
1780541591	12.68 Volt	10 Pkt	100 Pcnt
1780540391	12.68 Volt	0 Pkt	100 Pcnt
1780539191	12.68 Volt	0 Pkt	100 Pcnt
1780537991	12.68 Volt	0 Pkt	100 Pcnt
1780536791	12.68 Volt	0 Pkt	100 Pcnt
1780535591	12.68 Volt	0 Pkt	100 Pcnt
1780534391	12.68 Volt	0 Pkt	100 Pcnt
1780533191	12.68 Volt	0 Pkt	100 Pcnt
1780531991	12.68 Volt	0 Pkt	100 Pcnt
1780530791	12.68 Volt	0 Pkt	100 Pcnt
1780529591	12.68 Volt	0 Pkt	100 Pcnt
1780528391	12.68 Volt	0 Pkt	100 Pcnt
1780527191	12.68 Volt	0 Pkt	100 Pcnt
1780525991	12.68 Volt	0 Pkt	100 Pcnt
1780524791	12.68 Volt	0 Pkt	100 Pcnt
1780523591	12.68 Volt	10 Pkt	91 Pcnt
1780522391	12.68 Volt	10 Pkt	78 Pcnt
1780521191	12.68 Volt	10 Pkt	72 Pcnt
1780519991	12.68 Volt	10 Pkt	73 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)