OE3XDC-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3XDC-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1780557128	10.58 Volt	330 Pkt	80 Pcnt	22 C
1780556828	10.58 Volt	320 Pkt	80 Pcnt	22 C
1780556529	10.58 Volt	330 Pkt	80 Pcnt	22 C
1780556228	10.58 Volt	330 Pkt	80 Pcnt	21.5 C
1780555629	10.5 Volt	340 Pkt	81 Pcnt	22.5 C
1780555329	10.58 Volt	340 Pkt	81 Pcnt	23.5 C
1780555029	10.58 Volt	350 Pkt	81 Pcnt	25 C
1780554728	10.58 Volt	340 Pkt	80 Pcnt	23.5 C
1780554428	10.58 Volt	340 Pkt	79 Pcnt	23 C
1780554128	10.58 Volt	330 Pkt	78 Pcnt	21 C
1780553828	10.58 Volt	330 Pkt	78 Pcnt	20.5 C
1780553528	10.58 Volt	310 Pkt	77 Pcnt	22 C
1780553228	10.58 Volt	320 Pkt	77 Pcnt	22.5 C
1780552928	10.58 Volt	300 Pkt	75 Pcnt	21 C
1780552628	10.58 Volt	300 Pkt	74 Pcnt	21.5 C
1780552328	10.58 Volt	290 Pkt	72 Pcnt	22.5 C
1780552028	10.58 Volt	290 Pkt	72 Pcnt	21.5 C
1780551728	10.58 Volt	290 Pkt	73 Pcnt	21 C
1780551428	10.58 Volt	280 Pkt	72 Pcnt	21.5 C
1780551128	10.5 Volt	280 Pkt	72 Pcnt	20.5 C
1780550828	10.58 Volt	280 Pkt	72 Pcnt	19.5 C
1780550528	10.58 Volt	290 Pkt	73 Pcnt	20 C
1780550228	10.58 Volt	280 Pkt	70 Pcnt	19 C
1780549928	10.58 Volt	270 Pkt	69 Pcnt	18 C
1780549628	10.58 Volt	270 Pkt	68 Pcnt	18.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)