UR7D-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object UR7D-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*
1780535956	14.03 Volt	1280 Pkt	20 Pkt
1780535956	14.03 Volt	1280 Pkt	20 Pkt
1780535656	14.03 Volt	1280 Pkt	20 Pkt
1780535356	14.03 Volt	1280 Pkt	20 Pkt
1780535356	14.03 Volt	1280 Pkt	20 Pkt
1780535056	14.03 Volt	1280 Pkt	20 Pkt
1780534756	14.03 Volt	1280 Pkt	20 Pkt
1780534756	14.03 Volt	1280 Pkt	20 Pkt
1780534456	14.03 Volt	1280 Pkt	20 Pkt
1780534157	14.03 Volt	1280 Pkt	20 Pkt
1780534156	14.03 Volt	1280 Pkt	20 Pkt
1780533856	14.03 Volt	1280 Pkt	10 Pkt
1780533557	14.03 Volt	1280 Pkt	10 Pkt
1780533556	14.03 Volt	1280 Pkt	10 Pkt
1780533256	14.03 Volt	1280 Pkt	0 Pkt
1780532957	14.03 Volt	1280 Pkt	0 Pkt
1780532956	14.03 Volt	1280 Pkt	0 Pkt
1780532656	14.03 Volt	1280 Pkt	0 Pkt
1780532357	14.03 Volt	1280 Pkt	0 Pkt
1780532356	14.03 Volt	1280 Pkt	0 Pkt
1780532056	14.03 Volt	1280 Pkt	0 Pkt
1780531757	14.03 Volt	1280 Pkt	0 Pkt
1780531756	14.03 Volt	1280 Pkt	0 Pkt
1780531456	14.03 Volt	1280 Pkt	0 Pkt
1780531157	14.03 Volt	1280 Pkt	0 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)