SP8EBC-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8EBC-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Tx10min*	Vbatt*	Tempre*
1785293657	11 Pkt	12.5 V	10.5 DegC
1785293048	6 Pkt	12.52 V	10.5 DegC
1785292443	6 Pkt	12.5 V	10.5 DegC
1785291844	6 Pkt	12.52 V	10.5 DegC
1785291241	6 Pkt	12.54 V	10.5 DegC
1785290642	6 Pkt	12.56 V	10.5 DegC
1785290038	7 Pkt	12.56 V	10.5 DegC
1785289439	6 Pkt	12.56 V	10.5 DegC
1785288835	6 Pkt	12.56 V	10.5 DegC
1785288236	6 Pkt	12.56 V	10.5 DegC
1785287632	6 Pkt	12.56 V	11 DegC
1785287033	6 Pkt	12.58 V	11 DegC
1785286429	6 Pkt	12.58 V	11 DegC
1785285830	6 Pkt	12.58 V	11 DegC
1785285226	6 Pkt	12.58 V	11 DegC
1785284627	11 Pkt	12.6 V	11 DegC
1785284022	6 Pkt	12.6 V	11.5 DegC
1785283411	6 Pkt	12.6 V	11.5 DegC
1785282807	7 Pkt	12.6 V	11.5 DegC
1785282210	6 Pkt	12.6 V	12 DegC
1785281603	6 Pkt	12.62 V	12 DegC
1785281005	6 Pkt	12.62 V	12 DegC
1785280401	6 Pkt	12.64 V	12 DegC
1785279802	6 Pkt	12.62 V	12 DegC
1785279198	6 Pkt	12.64 V	12 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)