XE3JAC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object XE3JAC-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Voltage*	Temp*	Humidity*	Pressure*
1789961793	11.6 V	27 C	43 %	794 hPa
1789959992	11.6 V	27 C	43 %	794 hPa
1789958192	11.7 V	27 C	43 %	794 hPa
1789956391	11.7 V	27 C	42 %	794 hPa
1789954590	11.7 V	27 C	40 %	792 hPa
1789952790	11.6 V	27 C	40 %	792 hPa
1789950989	11.6 V	27 C	40 %	792 hPa
1789949188	11.7 V	27 C	40 %	790 hPa
1789947388	11.6 V	27 C	41 %	790 hPa
1789945587	11.6 V	27 C	41 %	790 hPa
1789943786	11.7 V	27 C	41 %	790 hPa
1789941986	11.6 V	27 C	41 %	790 hPa
1789940185	11.6 V	27 C	41 %	790 hPa
1789938384	11.6 V	27 C	41 %	790 hPa
1789936584	11.7 V	27 C	42 %	790 hPa
1789934783	11.7 V	27 C	43 %	792 hPa
1789932999	11.6 V	26 C	43 %	792 hPa
1789931182	11.6 V	26 C	43 %	792 hPa
1789929381	11.6 V	26 C	43 %	792 hPa
1789927580	11.6 V	26 C	41 %	792 hPa
1789925780	11.7 V	26 C	41 %	794 hPa
1789923979	11.6 V	26 C	42 %	794 hPa
1789922178	11.6 V	25 C	43 %	794 hPa
1789920378	11.6 V	25 C	43 %	794 hPa
1789918577	11.6 V	25 C	44 %	794 hPa

*Used Equation Coefficients:

Voltage: 0, 0.1, 0

Temp: 0, 1, -40

Humidity: 0, 1, 0

Pressure: 0, 2, 500

Unused: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)