DM2OV-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DM2OV-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1780888779	19.2 deg C	64.4 %	1019.5 hPa
1780887877	19.3 deg C	64.4 %	1021 hPa
1780886975	19.3 deg C	64.4 %	1019.3 hPa
1780886076	19.4 deg C	64.4 %	1021.1 hPa
1780885180	19.5 deg C	64.4 %	1022.3 hPa
1780884278	19.5 deg C	64.4 %	1026.7 hPa
1780883379	19.6 deg C	64.4 %	1023.6 hPa
1780882478	19.7 deg C	64.4 %	1020.4 hPa
1780881575	19.7 deg C	64.3 %	1024.1 hPa
1780880673	19.8 deg C	64.3 %	1023.6 hPa
1780879773	19.8 deg C	64.3 %	1022.9 hPa
1780878873	19.9 deg C	64.3 %	1022.3 hPa
1780877970	20 deg C	64.2 %	1022.9 hPa
1780877065	20 deg C	64.3 %	1020.8 hPa
1780876169	20.1 deg C	64.3 %	1025.2 hPa
1780875267	20.1 deg C	64.2 %	1023.9 hPa
1780874363	20.2 deg C	64.2 %	1025.7 hPa
1780873457	20.2 deg C	64.2 %	1022.7 hPa
1780872555	20.3 deg C	64.1 %	1024 hPa
1780871653	20.4 deg C	64.1 %	1023.2 hPa
1780870756	20.5 deg C	64 %	1023.8 hPa
1780869851	20.5 deg C	64 %	1022.2 hPa
1780868952	20.6 deg C	63.8 %	1021.6 hPa
1780868054	20.7 deg C	63.7 %	1024.6 hPa
1780867157	20.8 deg C	63.6 %	1023.3 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)