IQ3FX-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IQ3FX-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784779887	12.68 Volt	630 Pkt	62 Pcnt
1784779587	12.68 Volt	630 Pkt	62 Pcnt
1784779287	12.68 Volt	640 Pkt	62 Pcnt
1784778991	12.68 Volt	650 Pkt	62 Pcnt
1784778687	12.68 Volt	660 Pkt	61 Pcnt
1784778388	12.68 Volt	670 Pkt	62 Pcnt
1784778088	12.68 Volt	660 Pkt	62 Pcnt
1784777791	12.68 Volt	660 Pkt	62 Pcnt
1784777488	12.68 Volt	650 Pkt	62 Pcnt
1784777188	12.68 Volt	650 Pkt	61 Pcnt
1784776888	12.68 Volt	650 Pkt	61 Pcnt
1784776588	12.68 Volt	670 Pkt	62 Pcnt
1784776288	12.68 Volt	650 Pkt	62 Pcnt
1784775988	12.68 Volt	640 Pkt	62 Pcnt
1784775688	12.68 Volt	640 Pkt	61 Pcnt
1784775388	12.68 Volt	650 Pkt	62 Pcnt
1784775088	12.68 Volt	620 Pkt	62 Pcnt
1784774788	12.68 Volt	620 Pkt	61 Pcnt
1784774488	12.68 Volt	600 Pkt	60 Pcnt
1784774188	12.68 Volt	620 Pkt	60 Pcnt
1784773888	12.68 Volt	610 Pkt	60 Pcnt
1784773588	12.68 Volt	600 Pkt	61 Pcnt
1784773288	12.68 Volt	600 Pkt	61 Pcnt
1784772988	12.68 Volt	590 Pkt	62 Pcnt
1784772688	12.68 Volt	600 Pkt	63 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)