W4IJG-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W4IJG-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Batt_V*	Uptime*	Cap_Rem*
1788652752	13.7 Volts	15 Hrs	100 %
1788652750	13.7 Volts	15 Hrs	100 %
1788652747	13.7 Volts	15 Hrs	100 %
1788524496	13.6 Volts	29 Hrs	100 %
1788523896	13.6 Volts	29 Hrs	100 %
1788523294	13.6 Volts	29 Hrs	100 %
1788522693	13.6 Volts	29 Hrs	100 %
1788522093	13.6 Volts	29 Hrs	100 %
1788521493	13.6 Volts	28 Hrs	100 %
1788520294	13.6 Volts	28 Hrs	100 %
1788519691	13.6 Volts	28 Hrs	100 %
1788519091	13.6 Volts	28 Hrs	100 %
1788518489	13.6 Volts	28 Hrs	100 %
1788517889	13.6 Volts	27 Hrs	100 %
1788517288	13.6 Volts	27 Hrs	100 %
1788516689	13.6 Volts	27 Hrs	100 %
1788516087	13.6 Volts	27 Hrs	100 %
1788515487	13.6 Volts	27 Hrs	100 %
1788514886	13.6 Volts	27 Hrs	100 %
1788514285	13.6 Volts	26 Hrs	100 %
1788513685	13.6 Volts	26 Hrs	100 %
1788513085	13.6 Volts	26 Hrs	100 %
1788512485	13.6 Volts	26 Hrs	100 %
1788511885	13.6 Volts	26 Hrs	100 %
1788511285	13.6 Volts	26 Hrs	100 %

*Used Equation Coefficients:

Batt_V: 0, 0.1, 0

Charg_A: 0, 0.1, 0

Uptime: 0, 1, 0

Cap_Rem: 0, 1, 0

Tim_10%: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)