OK1TOM Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK1TOM. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1765625759	13.8 Volt	100 Pcnt	15.1 C
1765623959	13.8 Volt	100 Pcnt	15.1 C
1765622178	13.8 Volt	100 Pcnt	15 C
1765622178	13.8 Volt	100 Pcnt	15 C
1765620359	13.8 Volt	0 Pcnt	15 C
1765618559	13.8 Volt	0 Pcnt	15 C
1765617058	13.8 Volt	0 Pcnt	15 C
1765616759	13.8 Volt	100 Pcnt	15 C
1765614959	13.8 Volt	100 Pcnt	15 C
1765613159	13.8 Volt	100 Pcnt	14.9 C
1765611959	13.8 Volt	100 Pcnt	15 C
1765611359	13.8 Volt	100 Pcnt	15 C
1765609559	13.8 Volt	100 Pcnt	15 C
1765607759	13.8 Volt	100 Pcnt	14.9 C
1765606859	13.8 Volt	100 Pcnt	14.9 C
1765605959	13.8 Volt	100 Pcnt	15 C
1765604159	13.8 Volt	0 Pcnt	14.9 C
1765602360	13.8 Volt	100 Pcnt	15 C
1765601759	13.8 Volt	100 Pcnt	15 C
1765600560	13.8 Volt	100 Pcnt	15 C
1765598760	13.8 Volt	100 Pcnt	15 C
1765596960	13.8 Volt	100 Pcnt	15 C
1765596659	13.8 Volt	100 Pcnt	15 C
1765595160	13.8 Volt	100 Pcnt	15 C
1765593360	13.8 Volt	100 Pcnt	15 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)