HAMLTN Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HAMLTN. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1788573945	14.25 Volt	380 Pkt	100 Pkt	65 Pcnt
1788573645	14.25 Volt	430 Pkt	120 Pkt	67 Pcnt
1788573345	14.25 Volt	440 Pkt	120 Pkt	68 Pcnt
1788573044	14.25 Volt	430 Pkt	120 Pkt	67 Pcnt
1788572744	14.25 Volt	430 Pkt	120 Pkt	68 Pcnt
1788572457	14.25 Volt	430 Pkt	120 Pkt	68 Pcnt
1788572143	14.25 Volt	430 Pkt	120 Pkt	70 Pcnt
1788571843	14.25 Volt	420 Pkt	120 Pkt	70 Pcnt
1788571543	14.25 Volt	420 Pkt	120 Pkt	69 Pcnt
1788571243	14.25 Volt	420 Pkt	130 Pkt	70 Pcnt
1788570942	14.25 Volt	440 Pkt	140 Pkt	71 Pcnt
1788570642	14.25 Volt	450 Pkt	150 Pkt	72 Pcnt
1788570342	14.25 Volt	410 Pkt	120 Pkt	70 Pcnt
1788570041	14.25 Volt	370 Pkt	100 Pkt	69 Pcnt
1788569741	14.25 Volt	370 Pkt	100 Pkt	70 Pcnt
1788569441	14.25 Volt	380 Pkt	100 Pkt	72 Pcnt
1788569141	14.25 Volt	400 Pkt	110 Pkt	72 Pcnt
1788568854	14.25 Volt	410 Pkt	120 Pkt	72 Pcnt
1788568540	14.25 Volt	420 Pkt	110 Pkt	73 Pcnt
1788568240	14.25 Volt	440 Pkt	120 Pkt	72 Pcnt
1788567939	14.25 Volt	450 Pkt	120 Pkt	73 Pcnt
1788567639	13.88 Volt	450 Pkt	110 Pkt	72 Pcnt
1788567339	14.25 Volt	430 Pkt	100 Pkt	72 Pcnt
1788567039	14.25 Volt	450 Pkt	90 Pkt	73 Pcnt
1788566738	14.25 Volt	470 Pkt	90 Pkt	74 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

TEMP1: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)