SNKRVR Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SNKRVR. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1761526680	13.13 Volt	350 Pkt	66 Pcnt
1761524880	13.43 Volt	330 Pkt	74 Pcnt
1761523080	13.5 Volt	370 Pkt	77 Pcnt
1761521280	13.43 Volt	340 Pkt	72 Pcnt
1761519480	13.5 Volt	290 Pkt	68 Pcnt
1761515880	13.5 Volt	300 Pkt	69 Pcnt
1761514080	13.43 Volt	280 Pkt	67 Pcnt
1761512281	13.5 Volt	310 Pkt	74 Pcnt
1761510480	13.43 Volt	310 Pkt	76 Pcnt
1761508680	13.5 Volt	310 Pkt	77 Pcnt
1761506880	13.43 Volt	290 Pkt	81 Pcnt
1761505081	13.5 Volt	300 Pkt	81 Pcnt
1761503281	13.43 Volt	310 Pkt	79 Pcnt
1761501481	13.5 Volt	300 Pkt	78 Pcnt
1761499681	13.43 Volt	310 Pkt	72 Pcnt
1761497881	13.5 Volt	360 Pkt	67 Pcnt
1761496081	13.43 Volt	430 Pkt	71 Pcnt
1761494281	13.5 Volt	430 Pkt	73 Pcnt
1761492481	13.43 Volt	330 Pkt	69 Pcnt
1761490681	13.5 Volt	310 Pkt	71 Pcnt
1761488881	13.43 Volt	290 Pkt	73 Pcnt
1761487081	13.5 Volt	290 Pkt	65 Pcnt
1761485281	13.43 Volt	290 Pkt	60 Pcnt
1761483481	13.5 Volt	290 Pkt	55 Pcnt
1761481681	13.43 Volt	290 Pkt	56 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)