SQ7BCZ-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ7BCZ-14. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Temp*
1784705486	12.68 Volt	2 Pkt	21 C
1784703686	12.68 Volt	2 Pkt	20.5 C
1784701886	12.68 Volt	2 Pkt	20.5 C
1784700086	12.68 Volt	2 Pkt	20.5 C
1784698286	12.68 Volt	4 Pkt	20 C
1784696486	12.68 Volt	4 Pkt	19.5 C
1784694686	12.68 Volt	2 Pkt	17 C
1784692886	12.68 Volt	2 Pkt	19 C
1784691086	12.68 Volt	2 Pkt	21 C
1784689286	12.68 Volt	2 Pkt	21.5 C
1784687486	12.68 Volt	2 Pkt	21.5 C
1784685686	12.68 Volt	2 Pkt	21.5 C
1784683886	12.68 Volt	2 Pkt	21.5 C
1784682086	12.68 Volt	2 Pkt	21.5 C
1784680287	12.68 Volt	2 Pkt	21.5 C
1784678487	12.68 Volt	2 Pkt	21.5 C
1784676687	12.68 Volt	2 Pkt	21.5 C
1784674887	12.68 Volt	3 Pkt	22 C
1784673087	12.68 Volt	2 Pkt	22 C
1784671287	12.68 Volt	2 Pkt	22 C
1784669487	12.68 Volt	2 Pkt	22 C
1784667687	12.68 Volt	2 Pkt	21.5 C
1784665887	12.68 Volt	2 Pkt	21.5 C
1784664087	12.68 Volt	2 Pkt	21.5 C
1784662287	12.68 Volt	2 Pkt	20.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 1, 0

Dg1h: 0, 1, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)